AU.jpg?x-oss-process=image/format,webp)
Explore VEVOR's full line of plastic strip curtains for walk-in coolers, loading docks, workshops, and garage doors. The range includes low-temperature, clear, and ribbed PVC in thicknesses from 0.06" to 0.12", widths of 6", 8", and 12", and heights that fit standard doors and full dock openings. Each kit comes with a mounting rail, brackets, and hardware, so you can install it the same day. This setup works for your opening and budget, whether you want to save money on refrigeration, keep dust in, or keep wind and bugs out.
Losing cool air every time a truck goes by? A garage door plastic curtain creates a movable wall that people, carts, and pallet jacks can push right through, then close behind them. VEVOR's PVC strip curtains save energy, keep the temperature stable, and keep dust, fumes, and pests where they belong. They are a cheap solution for both busy shop fronts and home sheds.
The material type determines how long a curtain will last, from two seasons to ten. Temperature, traffic, and what you need to stop all point to a specific formula.
The most common installation is clear, bendable PVC. Forklifts and people walking through the same doorway need to see it from both sides, which is important because it lets in a lot of light.
Standard grade handles temperatures between 10°F and 150°F, so it works for strip curtains on factory doors, in stockrooms, in production areas, and on garage doors. The 0.08" thickness in 8" width is the most common commercial specification. It strikes a good balance between durability and how hard it is to push through.
For doorways where people can walk through, choose thinner 0.06" material. Light hand pressure should be enough for everyone. If there is a lot of wind outside or the dock doors are very wide, you should go up to 0.12" because the extra weight helps prevent the plastic door strips from flapping around. Standard clear PVC strip doors offer the most benefits for garages and workshop walls at the lowest cost per opening.
Below freezing, regular PVC gets stiff and cracks. This is why cooler door strips and freezers use a special low-temperature formulation. This polymer mix stays flexible down to about -40°F, so strips don't break when they hit something. Instead, they keep swinging and sealing.
Also, walk-in freezer curtain strips bands keep the overlap tighter where it matters most by preventing frost buildup. Plastic freezer curtains are usually 0.08" thick or more and overlap by 50 to 66 percent. This is because every gap in the opening below zero makes the compressor run longer, and frost forms.
Standard grade usually works for coolers that are 32°F to 45°F, but the low-temp upgrade is cheap insurance for any business where doors constantly open and close. To make restocking easier, restaurants, food stores, and cold storage facilities often use low-temperature strip curtains across all refrigerated doors.
Plus, a few specialty grades solve certain problems better. Ribbed PVC has raised vertical ridges that keep the surface off of adjacent strips. This keeps clarity much longer and greatly reduces scratches in high-traffic areas.
Vinyl with an amber and red tint blocks UV wavelengths that flying insects like. This makes it a popular choice for food service doors, loading bays, and openings that lead outside. Dark red or green welding-grade curtains block spark flash while still letting supervisors see into the bay.
Electronics assembly and clean areas where charge buildup is a problem can use anti-static formulas. The mounting hardware stays the same no matter which version you choose. This means that a facility can use the same universal rail system and set of spare vinyl strips for doorways.
Before you order, measure the width and height of the finished opening. Then, choose the amount of overlap you want. Most interiors use a 50% overlap, while 66 to 100% overlap is typical for freezers, outdoor doors, and areas with strong winds or temperature differences.
Add about two inches to the height so the strips sit half an inch above the floor. They should be long enough to seal but not so long that they drag and curl at the ends. The bottom edge of the plastic strips for the doorway can scratch the floor and wear out after a few months.
You can mount the rail above the opening on a solid header by using the full-length aluminum track that comes with the kit instead of individual brackets. With universal fixing, you can remove and replace individual strips without taking apart the whole run. This makes maintenance on plastic door curtain strips quick and cheap.
Your material choice affects how much energy you save and how well the installation holds up to daily use.
Because they block convective airflow at the opening, thermal insulating strip curtains stop the biggest source of heat loss in cold rooms. When a properly overlapped curtain is installed on a cooler that is opened frequently, facilities usually notice a significant reduction in compressor cycling.
The most important factor is overlap. The sealed area almost doubles when the overlap goes from 50 percent to 100 percent, which is why cold storage operators insist on full overlap even though it costs more in materials.
A thicker gauge also helps stop the pressure difference that pulls strips apart. For the best result, pair the curtain with a door that you already have instead of getting a new one.
Waterproof plastic door curtains can be used in areas that require frequent cleaning or on wet processing floors without soaking up water or growing mildew. If the item will come into contact with food, make sure it meets USDA and FDA standards.
A vinyl curtain door also prevents noise from moving from the production area to the office area and dust from moving from the clean area into the air. Heat-sealed, rounded strip edges prevent cuts while handling and installing. Cleaning is easy: just use water and mild soap to wipe it down; do not use solvents. To save money in the long run, replace only the damaged strips instead of the whole curtain.
VEVOR stocks clear, ribbed, tinted, and low-temperature warehouse door strip curtains. They come in 6", 8", and 12" widths, as well as different thicknesses and sizes that can fit anything from a walk-in cooler to a full loading dock. We offer fast shipping and reliable post-sale customer service for all our kits, which come with the mounting rail and tools you need. Our prices are much lower than those at industrial supply stores. Do not spend money to cool the parking lot. Take a look at the collection right now, and close the deal this week.
For interior and general-use doorways, use a 50% overlap. Raise the level to 66% or 100% for freezers, doors that open to the outside, and areas with strong winds or large temperature differences.
Not at all. Below freezing, standard grade gets stiff and cracks. For walk-in coolers and other subzero storage needs, choose low-temperature materials that can handle temperatures down to about -40°F.
Before you cut the strips, measure the finished width and height of your opening. Then, add about two inches to the height so the strips hang just half an inch above the floor without dragging or curling.
Yes. With universal mounting rails, you can quickly remove and replace individual strips, so you do not have to replace the whole curtain because of a damaged piece.
Use warm water and light soap to wipe them down, and then dry them. Stay away from solvents and rough pads; they will cloud the surface and shorten the material's lifespan.
