Customer Reviews for VEVOR Combination Rolling Mill Machine Roller Width: 120 mm, Roller Diameter: 55 mm Rolling Mill Jewellery 85mm Roller Width Flat Rolling Manual Jewelry Press Tabletting Tool Jewelry DIY Tools

shockingly good for the money. the adjustments are not great, it is pretty loose and you need to watch you sizing as you do it cause the manual is wrong about the sizes. but, all things considered, its very heavy and built beautifully. its very simple, and just does what you need it to do. no bells, it just works.

This rolling mill could be better, but for the price I'd recommend it to a friend. First off, everything can be replaced, removed, fixed, adjusted. Everything on it is screwed or bolted together. It's easy to see what to take apart to be able to fix pretty much any problem with it. Get some feeler gauges they're really cheap, you can adjust the height of the rollers to keep them accurate throughout it's lifetime. This mill is amazing, it's my first mill, and I didn't spend much on it. For the price it's a great mill. I am able to melt any piece I'm upset or frustrated with, and turn it into new, usable sheet metal or wire. You can make square wire, fairly easily, just takes practice. I found if you make it round wire first, anneal it so it's soft. Then put it through the flat part, fairly hard pressure, so you can see what side is flattened. Then turn it to the side next to it. I tried flipping it 180 the first few times. Don't make my mistake, it will not line up no matter what on the sides. It wants to slide over to the side you already did and twist. Every. Time. Do one side at a time, in order. Then increase pressure when all 4 sides are done. You'll be pleasantly surprised with how professional the results are. It's easy to roll out wire or square wire, if you take your time, and adjust it very gradually. I melt my fine silver and my sterling on a piece of charcoal. I generally will carve a small mold cavity, just deep enough for the silver to not overflow. If you make it too deep it gets too hot and the silver starts to make the wood crack and the liquid silver fills the crack. It doesn't make a good ingot to work with. Keep the cavity shallow. Put your silver in the cavity. Cut back oxygen on your torch, and I put the mass of the flame right on it. It melts fast, make sure the flame is very orange before you try to melt it. more orange=less oxygen. Oxygen will make your silver bubble and crack when you mill it. That's what happened when I first got the mill.

Leider stimmen die Fotos im Netz und in der Beschreibung nicht mit der gelieferten Maschine überein. Die aufgepresste Mutter, mit der Madenschrauben, unter dem Oberteil ist in keinem Bild zu sehen. Die genaue Justierung der Rollen ist dadurch etwas schwierig.

So far so good. I like it. It works good. A bit loose in some areas, but workable.

Great little roller! I have made sheet and half round wire so far. I took 1 star off because the gear was rusted when it arrived. I cleaned and oiled it, it works OK but was a little disappointed. Still, I am loving making my own sheet and wire!

I have been very happy so far with this rolling mill. It functions well and I have very few gripes with it overall. My only issues are that it does not come with bolts to secure it to your work bench which is necessary and the hardware and design of how the crank attaches to the mill leaves alot to be desired. Other than that I would say any beginner looking to find a cheaper alternative to durston or pepe tools has found what they are looking for in the vevor rolling mill.

Buon prodotto. È piccolo quindi non riesce a laminare lingotti che superano i 6/7mm, ma funziona bene.

My rolling mill works great, the rollers came perfectly level(within .01mm between the highest and lowest spots), only issue it had was the main height adjustment gear came with a bunch of surface rust on it from the factory and needed a good amount of cleaning. everything else was fine though

Does what it says! Recommend 👍💯 1 tip: I'm missing a rubber foot so it doesn't slip.

It’s still going strong for me about a year later. I do this for a hobby, but I use it to make bezel wire, sheet, and use it for wire too and the half round has been nice too. All around good product for the price. Just make sure to keep it oiled so it doesn’t rust. I’ve done copper, brass, and silver with this. So it could for sure handle gold aswell.