Customer Reviews for VEVOR Pallet Forks, 1814 kg Capacity clamp on Pallet Forks, 1490 mm Tractor Bucket Forks, Heavy Duty Front Loader Attachment for Tractor, Loader Bucket, Skid Steer, Tractor Forks for Agriculture Farm

Bought with high hopes. The one pin to screw on isn’t screwing on properly. Needed a hammer in order to make it move. The forks wouldn’t stay on.

After installing these forks and using them for a while I have found them to be useful but really only because I only have a few things that require forks to lift. The most I am lifting are loads of about 500lbs. I must say that the fork itself feels very sturdy and they seem to be built like a tank. I say "seem" because unlike actual skid steer or similar forks these are made from rectangular box section rather than solid steel plate. Although they are heavy it is difficult to know the wall thickness of the box section and you are limited as to what you can pick up with these forks due to their very thick cross section. These forks will not fit under certain palettes. Again they have held up well with the loads I have lifted but I do not use palettes. These forks also stick out a long way in front of the bucket (in my case 60") and my bucket is 3 feet deep. That puts the load you are lifting a long way out in front of the skid steer and all of that load is being applied to only about 8 to 10 inches of the lip of the bucket. It really doesn't matter that they are rated for 4000lbs. The lip of the bucket will fail long before that 4000lbs could be lifted. The method by which they attach to the bucket is adequate for light loads but it is very difficult to attach the forks securely to the bucket. The large slot at the end of each fork slides over the lip edge of your bucket. Two "L" handle bolts on each fork fasten down on to the "lip" of the bucket clamping the forks in place. This is problematic for several reasons. First there are flared nut fittings that screw on to the ends of the "L" bolts where they clamp down on the bucket. One must be very careful to ensure these nuts have not travelled up the shaft of threaded "L" bolts while tightening. If they have it will be the sharp end of the "L" bolt that bites in to the surface of your bucket rather than the flared foot of the nut. Getting the "L" bolt tight enough while ensuring the flared nut is properly positioned to tighten against the bucket surface is difficult. Before I figured out that the flared nuts were NOT captive on the end of the "L" bolt, I had driven the end of one of the bolts half way through the surface of the metal clamping plate they give you to put between the bucket surface and the bolts. It is also difficult to tighten the "L" bolts enough to secure the forks in place. It is also important to install the forks over the bucket wear bands. This gives them something stronger to press against rather than just the sheet metal of the bucket. All in all these should be considered an inexpensive alternative to proper skid steer or tractor forks and only for light loads. I bought these because I could get them quickly and they allowed me to get my job done while waiting for my actual skid steer forks to arrive. Big difference between these at $175.00 vs. my skid steer forks at $2000.00.

I waited for a long time for the version with the stabilizer bar to become available for purchase and it never did. I reluctantly bought the ones without the stabilizer as they were needed sooner than later and thought I would just buy the stabilizer bar separately when it became available. A couple weeks later (of course) the set I originally wanted became available and I eagerly contacted Vevor for a stabilizer for my new forks, just to be told that it is not available for purchase separately and I should just sell this set of forks and buy a new set! Not impressed to say the least, one would expect parts and pieces/accessories of this nature to be available for your equipment down the line? We did come to an arrangement but I am still without my stabilizer bar I waited so long for. Do better please.

I had to modify the product. As delivered, it doesn't fit anywhere. The welds are incomplete, the workmanship is imprecise. It vibrates when moved. The fork joints are too weak and bend; I had to have a ring welded in between.

I purchased these 6 weeks ago. They arrived very quickly. The box was damaged. It looked like somebody taped part of a box over the original box. The parts bag was empty. It looked like somebody took the hardware out for a different set that was missing hardware and patched the box. It was missing all of the hardware to clamp to the bucket. Useless without it. I contacted customer support at least a dozen times. I get the run around. Parts are shipped. Parts are delayed. Please be patient. Here is a $15 credit. How about a $30 credit. I declined the credits as the forks are useless without the hardware, and I can't find the hardware that fits properly at the store. I have asked for a return several times, and keep getting different resolution options without getting me the hardware needed. I have asked that they take the hardware out of another box so that I can use the forks. Still no resolution. Frustrating.

Arrivé en 2 colis, les fourches dans un premier et le cadre avec les axes dans un second. L'acier semble solide et les soudures de qualité. Cependant, le matériel n'arrive pas avec les points de levage comme sur les photos du produits. J'ai donc du racheter ces elements en magasin afin de pouvoir l'utiliser en toute sécurité. Un point en moins egalement sur les points de fixation qui pourraient etre plus haut les 3 points qui descente parfois pas suffisamment: dans mon cas je suis tout juste si le terrain est plat et avec les bras au plus long.

Need some other way to hold them on. The clamps bent rite away.

Received the item and the bolts needed for the lower link were missing instead there were pins. This absolutely is incorrect I had to buy additional bolts to use for the lower link

Parts fairly heavy considering the cost. The pins to attach to 3 point hitch useless. It should come with proper boltst that attached to the 3 pt hit hitch. The bracket for that is weak point. If adding in cost to replace pins will not make it the good a price. If wanting to use with quick attachment bracket needs additional parts too. Somewhat satisfied.

Its hard to keep them for moving back and forth you can’t tighten them enough t on keep them from sliding under pressure