Customer Reviews for VEVOR Electric Honey Extractor 3 Frame Bee Extractor Stainless Steel Honey Spinner with Stand Beekeeping Equipment

Very good product. Will not actually use till spring. When the bees become active here.Excellent follow up and after sales service.

Arrived without delays, packed professionally. The hinges are designed for countersink bolts, however flat head bolts were supplied. The electric circuit cover was screwed on top of one of the hinges so I had to remove to and correct. The metal bracket on which the motor is mounted is arched down a little which causes the plastic lids not fully closing. The legs are a bit wobbly. All the above are minor issues, to be honest. The instruction could have been printed a bit better (unclear) using a bit better English. Despite the above, assembling was quite easy and quick. Before I used it I had to clean the grease from the inside of the axle base (why put grease where it would mix with honey?). The motor is very quiet, the speed range is quite adequate. Being able to vary the speed is very important, as with full frames the device vibrates too much at higher speeds (which is expected as their weights would never be exactly the same). After most of the honey flew out I was able to crank the rotations to almost max. with only little vibrations. Overall I am satisfied, it does the job and it is a good value for money, in my opinion as far as a hobbyist-beekeeper like myself is concerned.

This honey extractor has the same issue like all extractors they can wobble around a fair bit when the honey frames are unbalanced. Just need fixing in place so they do not 'walk' across the floor when trying to extract honey. If the RPM could be slightly higher would make for a more timely extraction but gets the job done.

Works well as an extractor once you have stabilised it. The supplied legs are useless and cannot dampen the vibration of extracting. If you can change to stiffer legs it is a good working extractor for the price. Also make the new legs longer as original is too low to put a pail under with a strainer.

I've been waiting to do this review as I wanted to have used it a couple times first. I bought this extractor in Feb '24 and have used it 3 times. I was slightly concerned with some of the more negative comments, however, with that in mind decided to give this machine a try. Firstly, I am a hobbyist beekeeper and only do extractions about 2-3 times per year depending on flow. I have used the machine 3 times since Feb and extracted around 30+ frames of honey. The extractor is easy to use and does a very good job. The legs are a bit light and can cause more wobble than necessary, but I bolted the bases of the legs (they have holes cut out for this purpose) to a triangle of plywood and that firmed everything up. I attached locking castors to the bottom to easily move it around my shed. Also, you need to use your head a bit and think about using frames that feel close in weight to minimize the wobble at the start of extraction. If that isn't possible, go slow until the frames gradually become equal as the honey gets extracted, then speed up further. It is a bit of a "feel" thing, hard to explain, but easy to experience. The comments on having the honey gate too high are accurate, but with the legs locked into the plywood base you can easily tip the machine a bit to get the last of the honey out. But, this would be a good design improvement, if they made the honey gate lower. The motor is smooth and and works well. It did a great job of extracting the honey and supporting the frames during the process. It's all stainless steel and easy to clean. I take off the motor and pull out the baskets to clean everything after the extraction and it is quite simple to do (once you've done it for the first time). Beware, there is a ball bearing in the bottom center cup that the basket rod fits into, so if you turn the extractor over completely to get out any last water, that bearing can/will fall out. Just plunk it back in, reassemble and you're good to go. I also bought some food grade grease for the bearing maintenance. Overall, I am super happy with the extractor and it fits well for hobbyists.

Extractor works well, easy to assemble and use. A reverse function would be great on it but it doesn’t take much effort to flip the frames. The legs are a little flimsy but I just used the lower setting on them to reduce any movement. I would recommend this product to any backyard beekeepers

Unit arrived as advertised in quick time and in new condition. Legs had sharp edges that were removed easily with a file. The extractor worked perfectly but I feel that the legs may fail over time if the unit is screwed down tight and the frames are out of balance. This is the only minor fault I have. Otherwise very good. Overall I am very happy with the extractor. My wife and I used it and it worked perfectly.

The parcel arrived securely packaged with no damage. The extractor was easy to assemble by following the instructions. Everything was included as per the instructions. Whilst we haven't used it yet, it looks like it will do the job required. Happy with our purchase!

Bonne machine dans l'ensemble. Excepté le bouchon de vidange que j'ai du bricoler pour pouvoir le visser car le pas de vis n'était pas assez long. J'ai dû en acheter un autre mais que je vais devoir reprendre aussi a cause du diamètre qui doit être dans une mesure spéciale. Manque inverseur.

This honey extractor is quiet and efficient getting the job done, easy setup an easy to use 👌