Customer Reviews for VEVOR Ball Vise 3" Engraving Setting Tool 360°Rotation Professional Ball Vise 30 PCS Attachment Jewelry Engraving Block Tools Standard Block (3inch)

I haven't used it a ton yet, but it's a nice piece for start up.

The vice is well made. The attachments are the same as the GRC so if you wear them out you can upgrade the attachments by buying better-made ones.

Original GRS EQUIPMENT made in USA. BIG SURPRISE and fast delivery.

For the money this ball is a good value. Buyers will be much happier with the performance if they take it apart and give it a clean up. I did this by taking it apart removing all the oil, taking a file and removing all the sharp edged burs and bumps and putting small chamfer on all the sharp corners. I made a set of 220 and 320 grit sanding sheets for each half of the ball by cutting sheets in half and cutting a hole in the center for the center post to fit through. Put the ball back together ( with the bearing removed) with the sanding sheets in place and turn the halves against the sand paper for a while to smooth out these surfaces. I did this with the 220 and then 320 washed off both halves with solvent (WD40) and blew it all off with compressed air and wiped it down. Applied a thin film of teflon grease resembled the the ball, turned it a bunch to distribute the grease, then took it apart and wiped of all the excess. Reassembly with the bearing and the vise will spin 8 revolutions with one flick of the hand. When I got it it wouldn't make one full turn with the same effort. All in all I'm happy with this tool.

For the price it is a good tool

For the money this ball is a good value. Buyers will be much happier with the performance if they take it apart and give it a clean up. I did this by taking it apart removing all the oil, taking a file and removing all the sharp edged burs and bumps and putting small chamfer on all the sharp corners. I made a set of 220 and 320 grit sanding sheets for each half of the ball by cutting sheets in half and cutting a hole in the center for the center post to fit through. Put the ball back together ( with the bearing removed) with the sanding sheets in place and turn the halves against the sand paper for a while to smooth out these surfaces. I did this with the 220 and then 320 washed off both halves with solvent (WD40) and blew it all off with compressed air and wiped it down. Applied a thin film of teflon grease resembled the the ball, turned it a bunch to distribute the grease, then took it apart and wiped of all the excess. Reassembly with the bearing and the vise will spin 8 revolutions with one flick of the hand. When I got it it wouldn't make one full turn with the same effort. All in all I'm happy with this tool.

So this is not a high end GRS or Lindsay level quality but for the price it's great for a beginner or someone who is just engraving as a hobby. I read a lot of forums and reviews and half the people said these were total junk and to the pro who uses a lindsay or GRS everyday it probably is but for the begginer or someone who is just starting out and not sure they want to invest in an expensive vise I would say buy this and save your money for an airgraver.

As mentioned in other reviews, it comes with a real coat of grease. Since it has come from India, that seems entirely appropriate.I was cautious about getting a less expensive engraving vise, but I am very happy with this one. Everything I see is better quality than you might expect for a vise that is 1/3 to 1/2 the cost of many others, but I am quite happy with it. It really IS fifteen pounds!I was not sure if I needed the accessories, but I am very happy I purchased the one WITH the accessories.If I ever have the need for a second one, I'll get one of these.WARNING added a bit later:BE SURE you unpack this next to your trash barrel. As fast as you have any given box empty, put it in your trash barrel and then spray it once you are done. I got several "hitch hikers" (BUGS) in the packaging. I hope I killed them all.

Ball Vise Engraving Block 34pcs Attachment High Precise Setting Tool Engraver

I got the 5" and works great..have zero issues ...I highly recomend saving the money from buying a name brand version